Baaske Medical Silence TP 2 Specifications

- 9 - C. Intended Use The e-medic Silence TP 2 & TP 1 are designed to serve as a medical PC for general purpose usage in the hospital enviro

10 II. Product Basic A. Specifications Main System CPU: for TP 2 . Support Intel Core i Ivy Bridge ultra low power CPU w/ BGA1023 package, 17W

11 Life time 35 million activations Storage & Expansion HDD 2.5” SATA HDD drive bay x 1 + anti-vibration kit Expansion slot . PCI-E (x16) x 1

12 Altitudes . Operating: up to 3,000 m (9,842 feet) . Shipping: up to 12,192 m (40,000 feet) Pressure . Operating: 700 – 1060 hPa . Storage/Trans

13 B. The Packing / Outline / I/O / Control Buttons Basic packing list -- . The medical PC: e-medic Silence TP 2 (fanless) or TP 1 (smart fan)

14 . e-medic Silence TP 2 . The I/O interface (basic configuration)

15 . The control buttons & LED indicators Control buttons & LED indicators 1. HDD indicator: Dark - non-operating/stand-

16 C. Others . To clean or disinfect the system To clean or disinfect the system, to avoid any damage to the touch panel and the plastic housing,

17 Chemical Plastic housing 40% Sodium Hydroxid Damage Acetone Damage Carbitol Acetate Damage Cellosolve Acetate Damage Ethanol / Alcohol 500g

18 . The internal battery (optional) For those systems installed with internal battery, below is the specification. Battery cell type Lithium-Ion

- 1 - Table of Contents I. Safety & Regulatory Notice ... 2-9 A. Electronic Magnet

19 III. BIOS Immediately after powering on the system, during the POST (Power On Self Test) stage, press the <Del> key to enter t

20 Advanced -- Launch OpROM Support Launch PXE OpROM Enables or disables Boot Option for Legacy Network Devices. Launch Storage OpROM Enable

21 Extended Tag If ENABLED allows Device to use 8-bit Tag field as a requester. No Snoop Enables or Disables PCI Express Device No Snoop option. Ma

22 Core-Multi Processing Enable or Disable Core-Multi Processing mode. Execute Disable Bit XD can prevent certain classes of malicious buffer overf

23 TV1 Standard TV2 Standard Active LFP Select the Active LFP Configuration. No LVDS:VBIOS does not enable LVDS. INT-LVDS:VBIOS enables LVDS driv

24 Serial Port 3 Configuration Set Parameters of Serial Port 3 (COM E). Serial Port 4 Configuration Set Parameters of Serial Port 4 (COM F). Serial

25 Chipset -- Host Bridge/South Bridge This screen provides information on Host Bridge/South Bridge parameters.

26 Boot -- Setup Prompt Timeout Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting. Bootup Numlock St

27 Always Do not allow disabling GA20. Option ROM Messages Sets display made for option ROM. Interrupt 19 Capture Enables or disables Option

28 Security – Enables or disables the security chip. It is recommended that you use this function with the Administrator/User password.

- 2 - I. Safety & Regulatory Notice A. Electronic Magnetic Compatibility Guidance and manufacturer’s declaration – electromagnetic emi

29 Save & Exit – Save Changes and Exit Exit system setup after saving the changes. Discard Changes and Exit Exit system setup without sav

30 Baaske Medical GmbH & Co. KG Bacmeisterstr. 3 32312 Lübbecke Tel: +49 5741 236027 – 0 Fax: +49 5741 236027

- 3 - The e-medic Silence TP 2 & TP 1are intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. T

- 4 - discharge (ESD) IEC 61000-4-2 ±8 kV air ±8 kV air concrete or ceramic tile. If floors are covered with synthetic material, the relative hum

- 5 - Power frequency (50/60 Hz) magnetic field IEC 61000-4-8 3 A/m 3 A/m Power frequency magnetic fields should be at levels characteristic of

- 6 - distance in meters (m). Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey, a should be less than t

- 7 - B. Safety ISO 7000-0434 : CAUTION, consult ACCOMPANYING DOCUMENTS. ISO 7000-1641 : Follow operating instructions or Consult instructions

- 8 - Collateral standard: Safety requirements for Medical electrical systems – EN 60601-1-2 (IEC 60601-1-2) Medical electrical equipment Part 1